QUESTION 61
Users in a small location report that they often receive a busy signal during peak office hours. The site WAN connection does not look like it is saturated. The site does not use video calls, but they require good quality audio from the site to headquarters. QoS is configured on the WAN link with Cisco routers. All devices are registered on the headquarters Cisco UCM cluster. What is the root cause of this problem?
A. The subzone is configured with a maximum number of calls, which is now peaking.
B. The SIP trunk is configured with a maximum number of calls, which is now peaking
C. The zone is configured with a maximum number of calls, which is now peaking.
D. The location is configured with a maximum bandwidth for audio calls, which is now peaking
Correct Answer: D
QUESTION 62
An administrator is configuring Cisco UCM and wants all inbound calls to the company’s published DID number to ring on the receptionist’s internal directory number. Which configuration step meets this requirement?
A. Create a translation pattern for the main number and map it to the receptionist’s number.
B. Create a transformation patter for the main number and map it to the receptionist’s number.
C. Create a route pattern for the main number and map it to the receptionist’s number.
D. Create a call park for the main number and map it to the receptionist’s number.
Correct Answer: A
QUESTION 63
An administrator is configuring an Intercluster Lookup Service between 10 Cisco UCM clusters. Due to security requirements, certificate-based authentication must be used. Due to the deployment size, the administrator wants to avoid manually exchanging certificates between the clusters. Which two steps must be followed to meet these requirements? (Choose two.)
A. Install multiserver CA-signed CallManager certificates on all cluster publishers.
B. Enable password-based authentication in conjunction with certificate-based authentication.
C. Install multiserver CA-signed Tomcat certificates on all cluster publishers.
D. Set all clusters to standalone on the ILS configuration page.
E. Ensure that the cluster ID for all clusters is the same.
Correct Answer: BC
QUESTION 64
A company has a small sales office in a large city. This office is used by traveling sales personnel that need a temporary desk while they are in the city. The users want to make sure that they have a desk phone with their phone number, service links, and speed dials while they use this desk. Which configuration supports this requirement?
A. Cisco Extension Mobility
B. Cisco Unified SNR
C. Cisco DevicePool Mobility
D. Cisco FindMe
Correct Answer: A
QUESTION 65
A company with only 15 users needs to have a phone system without deploying dedicated servers for this purpose. Using the local Cisco router with Cisco UCME capabilities, which configuration is needed to support SIP phones?
A. voice-register SIP
B. voice-register pool
C. ephone
D. voice-register ephone
Correct Answer: B
QUESTION 66
An engineer needs to deploy the local route group feature to a Cisco UCM server by using the standard local route group. For each device pool, the engineer needs to specify a different PSTN access for emergency calls. What must the engineer do?
A. Add a new standard local route group. Select a route group as the new standard local route group in Device Pools. Create a route pattern of 911 that points to the new standard local route group.
B. Set a new local route group name. Select a route group as the new local route group in Device Pools. Create a route pattern of 911 that points to the new local route group.
C. Add a new standard local route group. Select a route group as the new standard local route group in Device Pools. Create a route pattern of 911 that points to a route list that contains the new standard local route group.
D. Create a new local route group name. In Device Pools, select a route group for that new local route group. Create a route pattern of 911 that points to a route list that contains the new local route group.
Correct Answer: D
QUESTION 67
An administrator wants to use the Call Queueing feature on Cisco UCM to allow new customers to wait in the queue while other agents are not available to take their call. Which configuration step enables this feature?
A. Call Routing > Route/Hunt > Hunt Pilot
B. Call Routing > Route/Hunt > Line Group
C. Call Routing > Route/Hunt > Hunt List
D. Call Routing > Route/Hunt > Call Park
Correct Answer: A
QUESTION 68
An engineer troubleshoots a problem with TEHO. Calling numbers that are not local to the MGCP PRI circuit are failing to route out. After troubleshooting with the carrier, it is determined that the customer must configure a mask so that calls that are routing out to the PSTN are displayed from a number that is registered to this circuit. What must the engineer configure to correct this problem?
A. The engineer must configure a “Calling Search Space” on the MGCP T1 port.
B. The engineer must configure a “Calling Party Transformation CSS” on the MGCP T1 port in Cisco UCM.
C. The engineer must configure the “Called Party Transformation CSS” on the gateway device pool.
D. The engineer must configure the “Called Party Transformation CSS” on the IP phone device pool.
Correct Answer: B
QUESTION 69
A company wants to use a Cisco phone system without the need for a local generic server. It is maximum 30 phones using a vendor-independent, industry-standard call protocol. What is the first command that must be entered to add this type of phone when registering a Cisco phone to this device?
A. voice register pool 3
B. ephone 3
C. voice register ephone 3
D. voice register sip ephone 3
Correct Answer: A
QUESTION 70
Users of a Cisco UCM want a conference number that they can use for quick conferences. Some prerequisites must be met to configure this feature for users of Cisco phones. The users are licensed with the Cisco Unified Workspace license, and the Cisco UCM cluster is set to a mixed mode for security. Which action must be taken to meet these requirements?
A. Add a CSS for Meet-me.
B. Add a softkey template.
C. Enable Meet-me in the Service parameter.
D. Add a partition for Meet-me.
Correct Answer: D
QUESTION 71
An engineer needs to configure a translation pattern in Cisco UCM to match dialed numbers that start with 9011 so that the calls can be routed with a single route pattern of +! If the engineer uses translation pattern 9011.! which two called party transformation settings must be configured in Cisco UCM? (Choose two.)
A. set Called Party Transform Mask to +!
B. set Discard Digits to Predot
C. set Called Party Number Type to International
D. set Prefix Digits (Outgoing Calls) to +
E. set Called Party Numbering Plan to International
Correct Answer: BC
QUESTION 72
An engineer configures several calling party transformation patterns in Cisco UCM so that calling numbers are shown in the +E.164 format. The route patterns match seven-digit internal numbers and prefix the numbers with 1408. The SIP trunk matches 1408XXXXXXX and prefixes the number with +. When users make outbound calls, the calling number still shows as seven digits. What is the cause of this problem?
A. The calling transformation on the route patterns is ignored because there is already a calling transformation on the SIP trunk.
B. Calling transformations cannot be configured on both route patterns and a SIP trunk.
C. The engineer must also apply a calling transformation at the route group details level.
D. The calling transformation on the SIP trunk is applied first, and then the calling transformation on the route patterns is applied.
Correct Answer: D
QUESTION 73
What is a capability of the gateway-preferred, network-based recording option in Cisco UCM?
A. It initiates when the application (recorder) dictates that it must be initiated.
B. Cisco UCM integrates with recording destination via SIP trunk.
C. It uses BIB of IP phone to fork audio to the recording destination.
D. It requires SIP trunk and CTI with recording application.
Correct Answer: B
QUESTION 74
A Cisco UCM-based solution uses URI-based calling for Cisco Jabber clients. The solution has several clusters in different locations. The solution being configured must have a secure method of exchanging addresses between the clusters. Which action ensures that a configuration complies with the requirements?
A. Select the TLS option on the SIP trunk between the clusters.
B. Assign a self-signed certificate to the ILS service trunk.
C. Exchange Tomcat certificates.
D. Apply a secure security profile to the trunk between the clusters.
Correct Answer: B
QUESTION 75
An engineer needs to deploy Cisco Extension Mobility. The engineer already activated the required services, configured the Extension Mobility Phone Service, and created an Extension Mobility device profile that is associated with end users. Which two additional steps are required to complete the configuration? (Choose two.)
A. Subscribe directory numbers to the Extension Mobility Phone Service.
B. Subscribe IP phones to the Extension Mobility Phone Service.
C. Define the default Device Template on IP phones when users log out.
D. Subscribe the device profile to the Extension Mobility Phone Service.
E. Consolidate Cisco UCM certificates by using Bulk Certificate Management.
Correct Answer: BC
QUESTION 76
What are two functions of the metadata in SIP recording? (Choose two.)
A. includes the details of the application media stream
B. contains the cryptographic context of the SRTP passthrough calls
C. carries the Agent Statistics Report
D. carries the communication session data (audio and video calls) that describes the call to the recording server
E. identifies the session and media association time
Correct Answer: DE
QUESTION 77
A newly deployed site in Pennsylvania uses SIP-to-SIP legs on a Cisco Unified Border Element. The administrator wants to match the incoming dial peer based on the calling number. Which configuration is needed in the dial-peer?
A. answer-address
B. destination calling
C. destination-pattern
D. incoming called-number
Correct Answer: A
QUESTION 78
An administrator is configuring a new deployment using Cisco Unified CME. The SCCP phones register without any issues, but SIP phones are not registering. Assume that all other configuration is valid. Which code allows SIP phones to register to Cisco UCME?
A. voice service voip
sip
bind media source-interface Vlan100
B. voice service voip
sip
registrar server expires max 600 min 60
C. voice service voip
sip
bind control source-interface Vlan100
D. voice service voip
allow-connections sip to h323
Correct Answer: B
QUESTION 79
A new solution is configured to support internal, local, and international calling. Calling [+44 1111 1111] from one of the registered internal phones does not work. Local and internal calls seem to work without any problems. The configuration has patterns configured to match the failing dialed number [+44 ……]. The other configured patterns show [2…] for internal numbers and [555 …] for local numbers. International numbers use E.164 as recommended. What is missing to make this solution work?
A. 001 or 00 must be used instead of the + sign on Cisco UCMI
B. in front of the +
C. / in front of the +
D. =+ cannot be used in a route pattern, only in a SIP pattern
Correct Answer: B
QUESTION 80
Some users report having issues dialing some external numbers when travelling to other locations within the company. The company has five locations in five cities in one country and has an egress gateway in each location for TEHO. The configuration has no specific entry stating that the roaming users are using the local gateway, but calls are going out. How is a verification of the call routing in such a specific configuration performed to further identify the problem?
A. local route groups
B. device mobility
C. standard local route group
D. TEHO
Correct Answer: A