QUESTION 21
A domain ID conflict is detected on a Cisco MDS 9000 Series Switch. Which action resolves the issue?

A. Issue an fcdomain disruptive restart.
B. Perform a fcdomain nondisruptive restart.
C. Issue a VSAN suspend/no-suspend.
D. Perform a complete domain manager fast restart.

Correct Answer: B

QUESTION 22
An engineer is troubleshooting a “Discovery Failed” error on a Cisco UCS C-Series server. The server is configured to be managed by the fabric interconnect directly. The engineer discovered that only the data connection is established with the fabric interconnect. Which port must be connected from the server to the fabric interconnect to resolve the issue?

A. mLOM port
B. PCIe port
C. MGMT port
D. CIMC port

Correct Answer: A

QUESTION 23
An engineer increased the number of links from the Cisco UCS 5108 Blade Server chassis to the Fabric Interconnect from a single link to four port channel links. However, Cisco UCS Manager did not register the change in the number of links, and the traffic flows through all available links. Which action resolves the issue?

A. Acknowledge the chassis.
B. Remove the chassis.
C. Decommission the chassis.
D. Reboot the chassis.

Correct Answer: A

QUESTION 24
A Cisco UCS C125 M5 server is integrated with Cisco UCS Manager using direct connect mode. The adapter for the server is reported as “inoperable” inside Cisco UCS Manager. Which action resolves the issue?

A. Match the adapter firmware to the Cisco UCS Manager version.
B. Reseat the adapter on the motherboard of the server.
C. Use a port expander with the vNIC adapter.
D. Connect the network cable to port 6 of the VNIC adapter.

Correct Answer: A

QUESTION 25
An engineer must upgrade the firmware of the Cisco UCS B-Series servers that are managed by Cisco UCS Manager. The upgrade must start immediately without automatically restarting the blade servers. Which action meets this objective?

A. Use maintenance policy with the reboot policy set to user-acknowledge.
B. Set the chassis global power policy to grid.
C. Set the Fabric Interconnect to switching mode.
D. Use the network control policy action when an uplink fails to issue a warning.

Correct Answer: A

QUESTION 26
An engineer must migrate a blade from UCS Domain A to UCS Domain B. The environment has these configurations:
1. B200 M5 contains a VIC 1440 that runs 4.0(4)B.
2. UCS Domain A is a Cisco UCS Fabric Interconnect 6248UP that runs 4.0(4)A.
3. UCS Domain B is a Cisco UCS Fabric Interconnect 6296UP that runs 3.1(3)A
4. Both domains use a Cisco UCS 5108 Chassis with 2208 IOM.

When the engineer inserts the blade into UCS Domain B, it fails to be discovered by Cisco UCS Manager. Which action resolves the issue?

A. Downgrade blade FW to 3.1(3)B
B. Add VIC 1480 mezzanine card
C. Upgrade UCS Domain B to 4.0(4)A
D. Replace VIC 1440 with VIC 1340

Correct Answer: C

QUESTION 27
A maintenance operation on power rail A caused a reboot of the servers in a Cisco UCS B-Series chassis. The Cisco UCS system has these attributes:
1. The system is equipped with four PSUs.
2. N+1 mode is used.
3. PSU 1 and 2 are connected to rail A.
4. PSU 3 and 4 are connected to rail B.

Which action prevents server reboot when rail A goes down?

A. Use N+2 mode; do not change physical plugs.
B. Configure N+1 mode with PSU1 and 2 on B and PSU3 and 4 on A.
C. Use GRID mode; do not change physical plugs.
D. Configure nonredundant mode with PSU1 and 3 on A and PSU2 and 4 on B.

Correct Answer: C

QUESTION 28
An engineer is suspecting an issue where there is a mismatch between RIB and FIB. The same prefix is learned via different routing protocols. Based on this output, from which protocol originated the prefix that was installed in the FIB?

Nexus1# show forwarding route 123.1.1.0 detail module 8
Prefix 123.1.1.0/24. No of paths: 1. Update time: Wed Jul 11 19:00:12 2018
Vobj id: 141 orig as: 65002 peer as: 65100 mh: 10.3.0.2
10.4.0.2 Ethemet8/4
packets: 2 bytes: 3484 Repair path 10.3.0.2 Ethernet8/3
bytes: 1

A. IS-IS
B. EIGRP
C. BGP
D. OSPF

Correct Answer: C

QUESTION 29
A Cisco ACI fabric consists of three tenants. User1 must have permission to manage only the PROD tenant. These configurations have already been completed:
1. The security domain TENANT has been created.
2. User1 has been created with the “write” privilege level.
3. User1 has access to all leaf nodes.

The configuration was deployed, but User1 still has access to all the other tenants. Which action resolves the issue?

A. Enable the restricted domain under security domain TENANT
B. Attach local user User1 to security domain all
C. Add local user User1 to the RBAC node rule
D. Associate security domain TENANT to tenant PROD

Correct Answer: D

QUESTION 30
Leafl# show fabric forwarding ip local-host-db vrf Test Telco | in 11.0.0.100
HMM host IPv4 routing table information for VRF EVPNA
Status: *-valid, x-deleted, D-Duplicate, DF-Duplicate and frozen, c-cleaned in 00:04:25
DF* 11.0.0.100/32 Vlan12 0x1420201 port-channe110

Refer to the exhibit. The endpoint 11.0.0.100 is frozen in the VXLAN fabric. Which command resolves the issue?

A. clear ip arp 11.0.0.100 vrf Test_Telco force-delete
B. delete ip arp 11.0.0.100 vrf Test_Telco force-clear
C. clear ip arp 11.0.0.100 vrf Test_Telco force-clear
D. delete ip arp 11.0.0.100 vrf Test_Telco force-delete

Correct Answer: C

QUESTION 31
A network engineer deployed a Cisco Nexus Dashboard but failed to change the management IP address for a single node cluster. Which action resolves the issue?

A. Clear browser cache.
B. Reconnect master node.
C. Recreate the cluster.
D. Replace the worker node.

Correct Answer: B

QUESTION 32
The Cisco UCS Manager fails to integrate with Cisco Intersight. The requirement is to monitor and configure the UCS environment from UCS Manager as well as Cisco Intersight. However, Cisco Intersight can monitor only the managed devices. Which action resolves the issue?

A. Allow Cisco IMC IP addresses of all the managed servers to reach Cisco Intersight.
B. Change the configured DNS server to resolve the Cisco Intersight IP address.
C. Set the Access Mode of Intersight Connector on the UCS to Allow Control.
D. Update the NTP settings on all the devices that Intersight manages to be in the same time zone.

Correct Answer: C

QUESTION 33
An engineer connected two Cisco UCS I/O modules to fabric interconnect with four links. When link 4 between the IOM-1 and primary fabric interconnect went down, the connectivity through lOM-1 from blade slots 3,4,7, and 8 failed over to lOM-2 and to the standby fabric interconnect. Which action allows traffic to fail back over to IOM-1?

A. Reseat the chassis.
B. Re-acknowledge IMO-1.
C. Re-acknowledge the chassis.
D. Reseat IMO-1.

Correct Answer: B

QUESTION 34
A SAN engineer must connect two previously configured Cisco MDS 9000 Series Switches to create a single fabric. When the E Ports are connected, the engineer receives a zone merge failure error message that is related to the zone set for VSAN 100 on each switch. Which command must be run on the newly added switch to resolve the issue?

A. zoneset copy active-zoneset full-zoneset
B. zoneset overwrite-control vsan 100
C. zoneset import interface fcl/l vsan 100
D. zoneset distribute full vsan 100

Correct Answer: D

QUESTION 35
Which location must be inspected to verify the creation of the backup file named bkp.timestamp.tgz within a Cisco UCS?

A. /workspace/backup of Equipment FSM page
B. /backup/workspace of Equipment FSM page
C. /workspace/backup of fabric interconnect
D. /backup/workspace of fabric interconnect

Correct Answer: D

QUESTION 36
A Cisco Nexus Dashboard consists of a single master node and three worker nodes, and the dashboard is integrated with a Cisco ACI Multi-Site fabric. An engineer notices that the Cisco ACI site is unavailable on the Nexus Dashboard. Which action resolves the issue?

A. Replace the master and worker nodes.
B. Export APIC configuration before the site is onboarded.
C. Re-add a different master node to the physical cluster.
D. Reregister the site in the Nexus Dashboard GUI.

Correct Answer: D

QUESTION 37
A host connected to port Eth0/1 on the Cisco Nexus Series Switch received this error:
*Mar 6 12:57:42.882:%PM-4-ERR_DISABLE: psecure-violation error detected on Eth0/1, putting Eth0/1 in err-disable state
*Mar 6 12:57:42.882:%PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address a527.cc72.3616 on port Ethernet0/1.

The server administrator concluded that the issue was caused by plugging the host in the wrong switch port and fixed the problem. Which action must be taken to recover the port from the error?

A. Shut and no shut the interface Eth0/1.
B. Install ENHANCED_LAYER2_PKG license.
C. Enable NETWORK_SERVICES_PKG license.
D. Change the interface Eth0/1 mode to access.

Correct Answer: A

QUESTION 38
An engineer is investigating traffic loss on a Cisco UCS B-Series blade server. The engineer discovers high rates of RX_CRC_STOMPED errors on the fabric interconnect ports to which the server traffic is pinned. Which action resolves the issue?

A. Update the firmware version on the virtual interface card adapter.
B. Configure the VLANs on the fabric interconnect.
C. Change the flow control settings on the I/O module.
D. Change the cables to fix physical connections.

Correct Answer: D

QUESTION 39
During the upgrade of Cisco UCS Infrastructure firmware, where is the latest backup file named “bkp.timestamp.tgz” stored?

A. /workspace/backup inside fabric interconnect
B. /workspace/backup inside blade chassis
C. File/workspace/backup inside blade chassis
D. File/workspace/backup inside fabric interconnect

Correct Answer: A

QUESTION 40
An engineer troubleshoots FCoE on a Cisco MDs 9o00 Series Switch. What does this output indicate about port channel 1?

MDS-8# show interface port-channel 1
port-channel1 is down (No operational members)
Hardware is Fibre Channel
Admin port mode is E, trunk mode is on
snmp link state traps are enabled
Port vsan is 1
5 minutes input rate 192 bits/sec,24 bytes/sec, 0 frames/sec
5 minutes output rate 0 bits/sec,0 bytes/sec, 0 frames/sec
380454 frames input,702340532 bytes
0 discards.0 errors
0 invalid CRC/FCS,0 unknown class
0 too long,0 too short
381988 frames output
0 discards,0 errors
8370 input OLS,4088 LRR,0 NOS,0 loop inits
6769 output OLS,6757 LRR, 4294 NOS, 1 loop inits
Member[1]: fc1/1 [down]
Member[2] : fc1/2 [down]

A. Port channel 1 is configured to connect to an NPV switch.
B. Port channel 1 is configured to connect to a host bus adapter.
C. Port channel 1 is configured to connect to an NPIV switch.
D. Port channel 1 is configured to be an ISL.

Correct Answer: D