QUESTION 1
A network engineer is implementing the Cisco ACI Fabric and notices that the Leaf-1 switch is registered has an assigned name, but is displayed as inactive in the APIC. After further investigation, it became clear that the leaf switch was recently moved from another Cisco ACI environment. Which action resolves the problem?

A. Define the new TEP address for Leaf-1.
B. Clean reload the Leaf-1 switch.
C. Change the clock offset from low to high between apic1 and Leaf-1.
D. Modify the ISIS interface peering IP address between apic1 and Leaf-1.

Correct Answer: B

QUESTION 2
An engineer configures FCoE between a set of ESXi hosts and a Cisco Nexus 5000 Series Switch. The Converged Network Adapter of the host fails to receive the response from the Cisco Nexus device. Also, the VFC interface is in a down state, and the FIP adapter fails to receive 802.1q tagged frames. The host interface is configured for VLAN trunking. Which action resolves the issue?

A. Set the bound Ethernet trunk interface to non-FCoE native VLAN.
B. Activate the reception of Xoff pause frames from the server.
C. Enable the active STP port state on the bound Ethernet interface.
D. Configure the UF link as a spanning-tree edge port.

Correct Answer: A

QUESTION 3
An engineer troubleshoots a Cisco UCS B-Series environment and discovers that the status of the CNA is degraded in the CLI and the Cisco UCS Manager GUI. What should be done to resolve the issue?

A. Install the adapter firmware version that is compatible with Cisco UCs Manager.
B. Seat the blade server correctly in the chassis.
C. Use the supported adapter on that server model.
D. Install the server air baffles correctly.

Correct Answer: A

QUESTION 4
After an upgrade, the standby supervisor of the Cisco N9K-C9504 Series Switch fails to boot and displays the message SYSMGR-2-STANDBY_BOOT_FAILED. Which action resolves the issue?

A. Reload the standby supervisor from the TFTP server.
B. Reload the active supervisor from the bootflash.
C. Reload the active supervisor from the TFTP server.
D. Reload the standby supervisor from the bootflash.

Correct Answer: D

QUESTION 5
An engineer is upgrading the Cisco UCS C240 M5 server’s firmware using the Non-Interactive Host Upgrade Utility (NIHUU) tool and the Python script. The ISO mapping is configured as CIFS and the mount option parameter is specified in the NIHU configuration file. However, the NIHUU fails to upgrade due to the ISO mapping error. Which action resolves the issue?

A. Enter BIOS setup and change the admin password.
B. Enable TLS 1.3 communication in the web browser.
C. Update and activate Cisco IMC firmware using XML API.
D. Download the software from USB flash drive.

Correct Answer: B

QUESTION 6
A Cisco UCS B-Series Blade Server is configured to boot a VMware ESXi host from an EMC VNX storage array by using a Fibre Channel SAN. The boot order is confirmed to be configured as expected, but the server fails to boot from the SAN. Which action resolves the problem?

A. Set the same WWNN pools for vHBA adapters.
B. Set the same WWPN pools for vHBA adapters.
C. Set the boot LUN to the highest LUN ID in the storage array.
D. Set the boot LUN to the lowest LUN ID in the storage array.

Correct Answer: D

QUESTION 7
Cisco UCS Manager raises a critical error message that indicates that the system has overlapping Ethernet and FCoE VLANs. All of the Ethernet traffic on the overlapping VLANs drops. Which action resolves the issue?

A. Modify the VLAN assignment to vNICs.
B. Change the PIN groups on the vHBAs.
C. Modify the FCoE VLAN.
D. Set the FCoE VLAN as the native VLAN on server uplinks.

Correct Answer: C

QUESTION 8
An engineer configures role-based access control for the Cisco UCS Manager. UserA must be allowed read-only access to the system. These events occur after the system is implemented:
1. UserA attempts to log in but receives an “Authentication Failed” message.
2. UserB successfully logs in by using an administrator role.
3. Both users use valid LDAP passwords.

Which action resolves the issue?

A. Enable primary group rules for LDAP providers.
B. Add locales to the LDAP group map of UserB.
C. Assign a default role policy for remote users.
D. Add locales to the LDAP group map of UserB.

Correct Answer: C

QUESTION 9
An engineer upgrades Cisco UCS firmware from release 3.1(2) to release 3.1(3) using AutoInstall. Both fabric interconnects go offline during the software upgrade installation and issue multiple FSM retries in the DeployPollActivate stage. Which set of actions resolves the issue?

A. Acknowledge the error and reboot the primary fabric interconnect.
Clear the default firmware version and upload a new one.
Restart the upgrade process manually.
B. Clear the startup version of the default infrastructure and server pack.
Remove the service pack from the subordinate node.
Upgrade with the Force attribute through AutoInstall
C. Enable the management interface monitoring policy on the fabric interconnects.
Initiate a configuration backup on both fabric interconnects.
Commit the pending fabric interconnect reboot activity.
D. Fix the rights to 666 with the debug plugin on the primary fabric interconnect.
Save the current configuration on the running fabric interconnect.
Continue the upgrade on both fabric interconnects.

Correct Answer: B

QUESTION 10
A network engineer troubleshoots an issue at a Cisco data center environment with these conditions:
1. The data center has Cisco Nexus 9000 Series Switches running the vPC setup.
2. The gateway of the servers is an HSRP IP address between the VLAN interfaces configured on both Cisco Nexus switches.
3. Some of the client application servers are implementing fast-path forwarding for the return traffic.
4. Those servers are sending the return traffic to the VLAN interface MAC address instead of the HSRP MAC address.

The network engineer discovers that some traffic is dropped because it passes the vPC peer link to be forwarded out the vPC interface. What must be configured on the vPC switches to resolve the issue?

A. peer-gateway
B. arp synchronize
C. peer-switch
D. spanning-tree

Correct Answer: A

QUESTION 11
A Cisco UCS c-Series Server powers off due to a power outage. The server should turn on when the power is restored with a fixed delay of 3 minutes. However, it remained powered off for more than 3 minutes after the engineer powered it back online. Which two actions resolve the issue? (Choose two.)

A. Set the delay fixed value to 3.
B. Configure the power restore last-state policy.
C. Configure the power-restore-policy.
D. Set the delay value to 180.
E. Configure power sync policy.

Correct Answer: CD

QUESTION 12
An FSM failed during an upgrade with the auto-install feature enabled. The engineer must remove the service pack from the subordinate fabric interconnect (FI) to recover the FIs. Which set of commands resolves the issue?

A. UCS-A# scope fabric-interconnect b
UCS-A# /fabric-interconnect # remove service-pack
UCS-A# /fabric-interconnect* # commit-buffer
B. UCS-A# scope org
UCS-A /org # scope fw-infra-pack default
UCS-A /org/fw-infra-pack # set infra-bundle-version “”
UCS-A /org/fw-infra-pack* # commit-buffer
C. UCS-A# scope org
UCS-A /org #f scope fw-infra-pack default
UCS-A /org/fw-infra-pack # set infra-bundle-version “”
UCS-A# /fabric-interconnect # remove service-pack security
UCS-A# /fabric-interconnect* # commit-buffer
D. UCS-A# scope fabric-interconnect b
UCS-A# /fabric-interconnect # remove service-pack security
UCS-A# /fabric-interconnect* # commit-buffer

Correct Answer: D

QUESTION 13

Refer to the exhibit. Two Cisco Nexus Series Switches have been configured to form OSPF neighborship. Which action resolves the issue?

A. Configure ACL to allow multicast IP on the OSPF interface
B. Configure the same authentication password on both switches
C. Configure the switch ID of the neighbor as 10.10.100.2
D. Configure the same MTU values on adjacent interfaces

Correct Answer: C

QUESTION 14
An engineer deploys a Cisco fabric network based on spine-leaf architecture. Cisco DCNM has been integrated to support the automation of a virtual network service of a firewall. After integration, the engineer observes that the host traffic does not reach the firewall node. Which action resolves the issue?

A. Update the host node IP address in DCNM.
B. Delete the service node IP address in DCNM.
C. Complete the service configuration parameters.
D. Configure the required profile for the host network.

Correct Answer: D

QUESTION 15
An engineer performs a Cisco B-Series firmware upgrade using a host firmware pack and AutoInstall server feature on an adapter. The adapter activation stops at the pending-next-boot state. The issue occurs at the adapter activation stage during the BIOS and adapter update process. Which set of actions resolves the issue?

A. Set the Activate status on the adapter to Ready.
Reset the server.
B. Log in to Cisco UCS Manager.
Reset the adapter.
C. Disable the fabric services.
Reboot the server.
D. Revert the BIOS to the prior working version.
Reboot the operating system

Correct Answer: A

QUESTION 16
A network engineer must configure SNMP monitoring on the Cisco Nexus 5000 Series Switch. The engineer issues the SNMP-server user testuser enforcePriv command but receives this message: “Unable to update CLI users database” Which change to permissions for testuser resolves the issue?

A. Add read permission.
B. Restrict read permission.
C. Add write permission.
D. Restrict write permission

Correct Answer: C

QUESTION 17
An engineer is troubleshooting an unexpected blade-server reboot. One of the DIMMs is displayed inside Cisco UCS Manager as “degraded with correctable errors” but is still available for the OS to use. Which action resolves the issue?

A. Reset the Cisco UCS chassis.
B. Reset the BMC.
C. Replace the DIMM.
D. Replace the CPU.

Correct Answer: C

QUESTION 18
A network engineer is attempting to integrate Cisco UCS Manager with Cisco UCS Central, but the integration fails. The engineer can ping Cisco UCS Central from Cisco UCS Manager. Which two actions resolve the issue? (Choose two.)

A. Synchronize Cisco UCS Manager and Cisco UCS Central by using NTP.
B. Assign the Cisco UCS Central license to Cisco UCS Manager.
C. Place Cisco UCS Manager on the same subnet as Cisco UCS Central.
D. Permit port 443 between Cisco UCS Manager and Cisco UCS Central.
E. Allow port 9443 between Cisco UCS Manager and Cisco UCS Central.

Correct Answer: AD

QUESTION 19
An engineer troubleshoots a VXLAN EVPN data center. The applications in the data center fail to reach the DNS server that is located at IP 10.10.10.10. The engineer examines the BGP EVPN routing table and notes that the IP prefix route that covers the DNS server is missing. Which action resolves the issue?

A. Configure an IP ARP entry to represent [4]:[0300.0000.XXXX.XXXX.XXXX]:[32]:[10.10.10.10]/136 in the routing table.
B. Configure an IP ARP entry to represent [2]:[0]:[0]:[48]:[XXXX.XXXX.XXXX]:[32]:[10.10.10.10]/272 in the routing table.
C. Set the IP prefix route to represent [5]:[0]:[0]:[32]:[10.10.10.10]/224 in the routing table.
D. Set the IP prefix route to represent [2]:[0]:[0]:[48]:[XXXX.XXXX.XXXX]:[0]:[0.0.0.0]/216 in the routing table.

Correct Answer: C

QUESTION 20
A network engineer performs a remote firmware upgrade in a Cisco ucs environment. The I/O module on the secondary fabric interconnects becomes inaccessble during the upgrade. There is no physical access to the chassis to reseat the I/O module. Which action resolves the issue?

A. Enable the firmware package.
B. Reset the peer I/O module.
C. Acknowledge the I/O module.
D. Activate Fault Suppression.

Correct Answer: B